AirNav RadarBox
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
 


Author Topic: DIY V-STUB ANTENNA MADE OF COAX  (Read 1792 times)

0 Members and 1 Guest are viewing this topic.

abcd567

  • Hero Member
  • *****
  • Posts: 842
  • CYYZ - Toronto
DIY V-STUB ANTENNA MADE OF COAX
« on: June 18, 2022, 12:55:01 AM »
DIY V-STUB ANTENNA MADE OF COAX

DIY V-Stub Antenna made of RG-6 coax. It can be made with any type of coax rated for 1 GHz or higher.

NOTE:
(1) On top, the small sliding piece of wire (with core insulation to hold the sliding wire in place) is for conveniently adjusting the length of top wire for best MESSAGE RATE (if no swr meter is available) or minimum SWR, if SWR meter is available.

(2) Being mechanically weak and prone to ingress of moisture inside the Coax, this antenna is NOT suitable for outdoor installation. It is intended for indoor installation near a window or in a balcony. Please see snapshot-2 below.




SNAPSHOT-1: ANTENNA CLOSEUP





SNAPSHOT-2: INDOOR INSTALLATION




Pigtail required to connect RG-6 coax to Radarbox Flightstick or FlightAware Pro Stick
30 / 50 / 60 cm, F-female to SMA-male pigtail RG316 / RG58 / RG174



OR




SWR MEASUREMENT RESULTS AFTER TUNING/TRIMMING TOP WIRE





COMPUTER SIMULATION RESULTS

Diagram 1 of 5: Geometry




Diagram 2 of 5: GAIN & Radiation Pattern




Diagram 3 of 5: SWR




Diagram 4 of 5: 3-D Radiation Pattern




Diagram 5 of 5: Current+Phase


« Last Edit: July 06, 2022, 10:59:19 PM by abcd567 »

abcd567

  • Hero Member
  • *****
  • Posts: 842
  • CYYZ - Toronto
Re: DIY V-STUB ANTENNA MADE OF COAX
« Reply #1 on: June 19, 2022, 10:13:24 PM »
BUILD FOR OUTDOOR INSTALLATION


For a stronger build, suitable for outdoor installation
(1) Use N-connector or SO239 connector.
(2) Use whip and radials made of 2mm or 2.5 mm dia wire .  Please see photos below.














.
« Last Edit: June 20, 2022, 04:43:05 AM by abcd567 »

ChrisGR

  • Full Member
  • ***
  • Posts: 144
Re: DIY V-STUB ANTENNA MADE OF COAX
« Reply #2 on: June 20, 2022, 10:07:08 AM »
You can explain the antenna theory, because the dimensions other than the sides of V and radials, do not correspond to a multiple of the wavelength.
Thank you.

abcd567

  • Hero Member
  • *****
  • Posts: 842
  • CYYZ - Toronto
Re: DIY V-STUB ANTENNA MADE OF COAX
« Reply #3 on: June 20, 2022, 04:27:36 PM »
You can explain the antenna theory, because the dimensions other than the sides of V and radials, do not correspond to a multiple of the wavelength.
Thank you.

For  Wire Collinear antennas, your requirement that all wire sections should necessarily be an exact multiple of wavelength, is not valid.

Please open and check dimensions of some successful commercial wire-collinear 1090 MHz antennas, or easier, please search the web for DIY wire collinear antennas,  and you will find a lot of these do not meet your requirement of "all wire sections necessarily be multiple of wavelength". Some, but not all, wire sections may meet your requirement.

I have run a computer simulation of this design to verify & optimized it's dimensions, and posted results in the very first post.  These results show it to be a good design (good gain, swr, and radiation paftern).

As the computer simulation software uses the laws & formulas of electromagnetic waves and their radiation, once the simulation software tells the dimensions give good gain,  swr,  and radiation patter,  it means the design conforms to electromagnetic wave theories.

In addition to confirmation by computerized simulation software,  I have checked it's performance by making it and doing a trial run, side by side with Flightaware 1090Mhz antenna, and compared results. The comparison proved that the V-Stub design performs good.


.
« Last Edit: June 20, 2022, 06:04:00 PM by abcd567 »

ChrisGR

  • Full Member
  • ***
  • Posts: 144
Re: DIY V-STUB ANTENNA MADE OF COAX
« Reply #4 on: June 21, 2022, 04:49:21 AM »
Thank you for explanation.
I thought it was a variation of half AMOS or Franklin antenna but the lengths were different.
May have a nice day
Chris