AirNav Systems Forum
AirNav RadarBox and RadarBox24.com => AirNav RadarBox and RadarBox24.com Discussion => Topic started by: gcopter1 on January 03, 2021, 07:18:39 PM
-
I recently downloaded the software and managed to point the software to my own Pi3 and adsb receiver.
If I click on the the Network tab and click the Get Flights from RadarBox network, I immediately get to see flights around me, not so when I deselect that and instead click the tab for My Flights.
On the File tab>Preferences>RadarBox New Firmware section, I've set the IP address of the Pi3 and the port it was using before for PlanePlotter.
If I open a webpage with the IP, I can see my data.
I rechecked Windows Firewall settings and ANRB is allowed.
What am I missing?
-
I believe it should be
Port: 32088
Host: 192.168.0.21
(replace 192.168.0.21 by your RPi's actual Local IP address)
Alan
-
Using 32088 as the port, didn't work.
If I use port 30005 (in my previous use with PP), the "Hardware Connected" box is lit green, but no aircraft showing.
-
Have you installed RB24 feeder on RPi?
It is the RB24 feeder which outputs ANRB v6 compatible output at port 32088.
The output at port 30005 is produced by dump1090 and in beast format. The ANRB although shows connected, does NOT process beast format data, so no planes will be displayed.
DUMP1090 PORT 30005 - DATA IN BEAST FORMAT - WONT BE PROCESSED BY ANRB V6
pi@raspberrypi:~ $ nc 127.0.0.1 30005
2i:gX▒▒|:▒^2i▒▒C ]▒▒▒k▒)3i▒▒:▒▒▒|e▒▒+2j˻X▒▒|:▒^2j▒▒X▒▒|:▒^3k9Hn▒▒▒|e▒▒
+3ka▒d▒▒▒~e▒▒ ▒▒c2k▒▒▒X▒▒|:▒^3k▒▒▒▒▒|e▒▒
+2lX▒X▒▒|:▒^3l▒|▒▒▒|e▒▒ +2l▒▒X▒▒|:▒^3l▒Q
▒▒▒▒~e▒▒ ▒▒c3m4~▒▒▒▒|e▒▒ +2m▒eX▒▒|:▒^3ne▒▒▒|e▒▒
+2n▒]▒▒▒k▒/2n$(]▒▒▒k▒*2nb▒nX▒▒|:▒^3n▒▒▒▒▒▒|▒$▒Hj3n٥K▒▒|e▒▒
+2n▒oX▒▒|:▒^3oQ▒▒▒▒~e▒▒ ▒▒cg3o▒▒▒▒▒|e▒▒
+2o▒▒▒X▒▒|:▒▒▒▒▒X▒▒~▒▒ު▒!2qu▒X▒▒|:▒^3qF▒z▒▒▒~e▒▒ ▒▒c^C▒▒▒▒,T2p=▒Y
]▒▒▒k▒!2p▒poX▒▒|:▒^3p▒
RADARBOX RPI FEEDER PORT 32088 - DATA IN SPECIAL FORMAT - WILL BE PROCESSED BY ANRB V6
pi@raspberrypi:~ $ nc 127.0.0.1 32088
FmJyZxQFBgoGAwQGBAQOAwYJAQ==~*
FmRjdBR0BgoOBAQYBQUKBgYJBgcCBwUHDQIaFBofHhgbGRQbGhQaHw==~*
FmRjdBR0BghwdgAYBQUKBgYJBgcCBwUHDQIaFBofHhgbGRQbGhQaHw==~*
FmRjdBR2DwABBXcYBQUKBgYJBgcCBwUHDQIaFBofHhgbGRQbGhQaHw==~
-
No I have not.
Could you please include the steps, it's been a couple of years since I began using my Pi.
I can access the pi via my browser, would I be able to add the RB feeder in this way or would I need to pull out the sd card?
Thanks.
-
Ok, I found the instructions on another thread.
If you don't mind, I'll ask follow up questions as I read the instructions.
Thanks.
Gilberto.
-
I'm following the instructions set in OPTION 3.
-
After typing "/list", I started seeing a lot of scrolling, seems like that command was doing a lot of updating.
At the end, I was presented with the option to install "dump978-rb program"
Waiting for y/n?
At this point, should I type "y"?
-
Went ahead and typed "y".
At the end of the process, I'm presented with a message.
What should I do next?
-
Takes a while for posts to show up.
Since last post, I entered "y" to accept the install.
After a bunch of scrolling, I found the entries to command the pi to get the key for the rb feeder.
My ARNB now works displaying my own flights.
Although on the pi, I saw lots of messages saying it couldn't connect to 978 something (forgot since I've already closed the pi browser).
Wondering if I should worry about it or leave things as is?
-
This will be you on RB24 I presume https://www.radarbox.com/stations/EXTSHA195452
Alan
-
Don't think so.
From the blue dot position on the map, that's located to the southwest of me.
-
Check, EXTRPI020773.
-
Edit your location with exact decimal lat/lon to set up MLAT
Alan
-
On the pi?
What's the command?
On the ANRB locale settings, is precise.
-
On RB24 EXTRPI020773 Top left grid where it states Click here to enter your location see attached
Alan
-
Although on the pi, I saw lots of messages saying it couldn't connect to 978 something (forgot since I've already closed the pi browser).
Wondering if I should worry about it or leave things as is?
You have said yes (y) to option to install dump978-rb. This requires plugging in RPi another dongle with its own antenna. Since you did not provide dump978-rb its dongle, it stsrts giving error messages.
Remove dump978-rb by following command
sudo apt-get purge dump978-rb
sudo reboot
.
-
Although on the pi, I saw lots of messages saying it couldn't connect to 978 something (forgot since I've already closed the pi browser).
Wondering if I should worry about it or leave things as is?
You have said yes (y) to option to install dump978-rb. This requires plugging in RPi another dongle with its own antenna. Since you did not provide dump978-rb its dongle, it stsrts giving error messages.
Remove dump978-rb by following command
sudo apt-get purge dump978-rb
sudo reboot
.
Thanks!
-
On RB24 EXTRPI020773 Top left grid where it states Click here to enter your location see attached
Alan
Sorry but, I don't see the option to click enter my location in the pic you included.
-
OK in that case contact [email protected] give them your account email address and your EXTRPI*** number and ask them to link the receiver to your account. Once done you will be upgraded to Business and will be able to download the RB24 app to your phone at no cost
Alan
-
Thanks.